GH1 firmware research volunteers required

I've sent a donation. I urge everyone to do the same right now. I was in charge of the HV firmware hack over on HV20.com for a long time, and progress there was/is very slow. It's crucial to enable a talented hacker like tester13 with equipment while he is in full swing. We learned the hard way over there that unless you have more than one guy working on it, it can all stall real quick. So fire off a donation right now - better small than none at all.

I don't actually have a GH1, I was waiting for a global-shutter GH2 (if the rumours are true), but if the hack manages to enable video out during recording (even just composite), higher bitrate and defeats AGC I might grab a couple.

I want them for stereo (3D) shooting, so being able to sync exposure parameters, white balance & focus between two cams would also be a huge deal.

Even better would be a way to precisely frame-sync video recording (ie. genlock-like), or at least start video recording at precisely the same time (any slow gradual drift is less of a problem). Frame sync is crucial in 3D when there's movement.
 
I've sent a donation. I urge everyone to do the same right now. I was in charge of the HV firmware hack over on HV20.com for a long time, and progress there was/is very slow.

As far as I remember camera had been bricked during attempts to dump firmware :-) I looked at this project closely some time ago .
And today I see quite a progress, camera just is very diffucult to reverse (different processors, and this FR thing, hate that).
It is very interesting to look at disassembled SD100, TM300 and TM700.
May be LSI is the same or very similar.
PAL switchability is very useful thing.

I was waiting for a global-shutter GH2 (if the rumours are true), but if the hack manages to enable video out during recording (even just composite), higher bitrate and defeats AGC I might grab a couple.

I do not believe in global shutter in this year. May be in 2012.
It required complete sensor redesign, and loss of NR and useful area.

And from commercial standpoint PAL/NTSC switchability will be most useful :-).
So, if any company want to donate specially for this to be priority, you are welcome.

I want them for stereo (3D) shooting, so being able to sync exposure parameters, white balance & focus between two cams would also be a huge deal.

I really don't know how it is possible to do.
May be thread monitoring USB . But it'll be real hard, as only Canon have full PTP commands engine (this is btw real reason of such good progress on Canon cameras).
Cameras can also drift with time.
 
Last edited:
Can someone donate a GH1 for testing? if they have 2 would anybody loan one out, I think Tester wont break it and maybe it would be fixable by Pana even if it was locked-out?
 
As far as I remember camera had been bricked during attempts to dump firmware :-)

Not quite, he flashed a mod into the wrong location (probably the boot loader).

I looked at this project closely some time ago .
It is very interesting to look at disassembled SD100, TM300 and TM700.

PM me your email address & I'll ask our hacker (jollyrogerxp) to contact you.

PAL switchability is very useful thing.

He recently found a service DV tape (without that tape & a particular remote control you cannot enter service mode on the HVs) and was apparently able to switch his NTSC HV20 to PAL. There was no option in the service menu, but it did allow him to change some EEPROM values and he had figured out which one it was. A lot of people said that PAL/NTSC is hardware- specific - that might have been true in the past but it's probably all in the firmware now.

I really don't know how it is possible to do.
May be thread monitoring USB . But it'll be real hard, as only Canon have full PTP commands engine (this is btw real reason of such good progress on Canon cameras).

I read somewhere that Panasonic do have comprehensive USB control, but they reserve it for their service engineers? Obviously this is advanced stuff, when the firmware is better understood, other programmers can try it (I'm a C++ programmer myself).
 
unless pana gets the chips pre-programmed, there should be some kind of programming header that could be used too.
 
PM me your email address & I'll ask our hacker (jollyrogerxp) to contact you.

If he don't have Panasonic cameras (like TM300) I don't know how he might help :-) But email address is available on site (or just add "info@" to site address).
I am not interested in HV20-HV30, as it is very good, but outdated camera.

A lot of people said that PAL/NTSC is hardware- specific - that might have been true in the past but it's probably all in the firmware now.

Yes, it is all firmware.

I read somewhere that Panasonic do have comprehensive USB control, but they reserve it for their service engineers? Obviously this is advanced stuff, when the firmware is better understood, other programmers can try it (I'm a C++ programmer myself).

May be. But without proper software it is hard to understand. I do not remember any strings related to such protocol.
Pentax also have very low level libraries for service centers.

I recently briefly looked at E-P1 firmware, and this is hackers dream with lot of debug menus, info, settings, strings. So if anyone is interested I could upload unpacker to my site (but note that I am not author here, author just want to remain unknown).
 
Regarding PAL/NTSC switch and other regional switches.
I have the service manual which says that when the main PCB is replaced it pops-up a question to enter the region code.
This code drives the supported languages as well as the supported TV standard PAL or NTSC.
After the option was selected the pop-up may not appear again, according to the manual.
 
Regarding PAL/NTSC switch and other regional switches.
I have the service manual which says that when the main PCB is replaced it pops-up a question to enter the region code.
This code drives the supported languages as well as the supported TV standard PAL or NTSC.
After the option was selected the pop-up may not appear again, according to the manual.

Yes, we have this manual.
And resetting all to factory settings is not good thing. You don't know condequences for calibration, etc. Also this setting can affect many other things and make camera unusable. Simple switch is much better. We could try to place it on some rarely used parameter, like VieraLink :-)
 
How much I'd like it to work, right now it does not. I have put it on a formatted SD card and still get No Valid Picture To Play. I am using the AC adapter. Could this be because I tried your firmware update test before? Did anyone else succeed in upgrading from 1.21? (Or is it 1.22?)
 
How much I'd like it to work, right now it does not. I have put it on a formatted SD card and still get No Valid Picture To Play. I am using the AC adapter. Could this be because I tried your firmware update test before? Did anyone else succeed in upgrading from 1.21? (Or is it 1.22?)

It can only be check performed on other version related constants.
[Deleted some stuff]

For guys with earlear firmwares - all must work.
 
Last edited:
Just donated! Has anyone that has installed the current firmware hack gotten native 24fps to work on 1080p and 720p? I would give it a try but I have my camera out on loan for a week or so. Just curious if anyone has gotten this working yet. Even if all that got accomplished with this project was native 24fps in 720p and 1080p then that is still a great accomplishment for the camera. It adds an important frame-rate to 720p and gets rid of an annoying extra step in 1080p!

Hopefully disabling AGC is next on list to start tackling!
 
OK.
Chibs - specially for you.
I added version patches to ptool, please, redownload it and try again.
Added patches are safe from my analysys of various firmware versions.
And as far as I understand only this parameters are checked.
 
downloaded, patched correctly 50p-60p -> 24p using makefps, and installed in gh1, it works!, now the camera shows firmware version 1.2

but unfortunately it does nothing, just recorded some videos in every mode and mud is still everywhere.

mud test is not very technical, but checking the video gives the same results:

resolution : 1280x720
framerate : 59.94
profile:level : High:4.0
bitrate real max : 16 051 020
avg (I) : 142 233
avg (P) : 27 928

the internal video structure is the same as before, 60 frames every second, I frame every 30 frames, P frames still get the muddy 27k per frame.

I'll do some more testings in the afternoon.
 
Last edited:
downloaded, patched correctly 50p-60p -> 24p using makefps, and installed in gh1, it works!, now the camera shows firmware version 1.2
but unfortunately it does nothing, just recorded some videos in every mode and mud is still everywhere.
mud test is not very technical, but checking the video gives the same results:

resolution : 1280x720
framerate : 59.94
profile:level : High:4.0
bitrate real max : 16 051 020
avg (I) : 142 233
avg (P) : 27 928

P frames still get the muddy 27k per frame.

It is to be expected.
And it could have saved me some time if I knew that it actually shoots at 59,94 as I already found some references related to this long time ago during reversing of video related procedures.
Check if available shutter speeds changed. As something related with FPS in AVCHD must change.
 
Last edited:
It is to be expected.
And it could have saved me some time if I knew that it actually shoots at 59,94 as I already found some references related to this.
Check if available shutter speeds changed. As something related with FPS in AVCHD must change.


also 30fps is actually 29.97, and 24p is 23.976, but the references in the code should be fractional, usually are 30000/1001 , 60000/1001 and 24000/1001.

will check later if something has changed in the camera.
 
One massive thank you to you! This worked perfect.
succes.jpg


I have donated 10$ for now, you're doing great work here.
 
Back
Top