GH1 firmware research volunteers required

Okey, thank you for note about digits table. ;-)

Testing must be the following:
1) Shooting very low details image (white paper, etc).
2) Shooting medium detail, out of focus image.
3) Focused normal interior image.
4) Glass, trees, very high detail images with good lightling

For each of four scenarios you must make separate clips. And one clip with all this together.
So it'll be possible to understand how it works.
 
Very interesting deal.

SD video DV compression is 25Mbit/s - Mjpeg
HD 720p Mjpeg 50Mbit/s it's very near same compression level.

My Sandisk can write 9Mb/s (70 Mbps) :-) I need new card..

;-) very nice result!
 
Last edited:
I don't get this:
the quality settings are "for 1080p30 only" but you provide an extra 1920 patch?
did you change the standard mjpeg 720p setting to 1080p? why the extra 1920 patch?
thanks
 
Quality settings (E1 to E4) - 352, 220, 200, 184
Table settings (E1 to E4) - 24, 24, 24, 24

Low complexity (white sheet)
QF (like Gordian Knot)............................0.831
Video Stream Length...............................3s 500ms
Video Stream BitRate..............................23.0 Mbps
Video Stream BitRate Mode.........................VBR
Video Stream Size.................................9.58 MiB (98%)

Medium Quality (out of focus)
QF (like Gordian Knot)............................1.828
Video Stream Length...............................2s 500ms
Video Stream BitRate..............................50.5 Mbps
Video Stream BitRate Mode.........................VBR
Video Stream Size.................................15.1 MiB (99%)

Complex (Leaves and movement)
Display Aspect Ratio..............................16:9
QF (like Gordian Knot)............................1.989
Video Stream Length...............................4s 500ms
Video Stream BitRate..............................55.0 Mbps
Video Stream BitRate Mode.........................VBR
Video Stream Size.................................29.5 MiB (99%)

Alltogether in one shot
QF (like Gordian Knot)............................1.637
Video Stream Length...............................15s 500ms
Video Stream BitRate..............................45.3 Mbps
Video Stream BitRate Mode.........................VBR
Video Stream Size.................................83.6 MiB (99%)

Dont know what QF means (first use of this tool called MediaInfo Mac). Hope it helps.
PS: its 720p. Why does it say "only for 1020p" in the description in ptool?
 
The mjpeg developments are great news. If 24 FPS could be achieved with 720p and maybe even 1080p with the better bit rate, etc. it would be fabulous. I like the stability, quality and easier post production of mjpeg. tester13 YOU ARE GOOD AT YOUR GAME!
 
If "real" 24fps mjpg were possible in 720p mode, with enhanced bitrate that would be delicious. Absolutely mud-free, great-looking hd at 24p...
 
So it doesn't seem that it is clear yet, whether or not the 24p MJPEG is still skipping frames or not...right?
 
So it doesn't seem that it is clear yet, whether or not the 24p MJPEG is still skipping frames or not...right?

Latest report it was but tester13 was concentrating more on bitrate and and stuff at this moment. Barry, if the Nikon D90 does 720p24 you think it could be possible to achieve it flawlessly on the GH1 with a hack? If anybody can do it tester13 would be the one!
 
Ok noob question here. Might be the dumbest questions but....What advantages will I have if I use the latest firmware? what disadvantages? Is there a how to on the pages here? I bought my Gh1 last feb and did not do any updates to it...should I have done so? I still don't have a pulldown program.....Should I buy a pulldown program or should I wait till a video editing program puts the pulldown into their product? If I do have to buy one....what program would you guys recommend? I know these are allot of questions but I know there is some of you out there that can answer all of them. Thanks
 
Ok noob question here. Might be the dumbest questions but....What advantages will I have if I use the latest firmware? what disadvantages? Is there a how to on the pages here? I bought my Gh1 last feb and did not do any updates to it...should I have done so? I still don't have a pulldown program.....Should I buy a pulldown program or should I wait till a video editing program puts the pulldown into their product? If I do have to buy one....what program would you guys recommend? I know these are allot of questions but I know there is some of you out there that can answer all of them. Thanks

Best to start a new thread for these questions.
 
Barry, if the Nikon D90 does 720p24 you think it could be possible to achieve it flawlessly on the GH1 with a hack?
Well, let's separate a few things out -- just because the Nikon can do it, bears no resemblance to what capabilities may or may not be in the GH1. Different hardware from a different manufacturer, so I don't think any conclusions can be drawn about what the GH1 could theoretically be capable of, based on some other manufacturer's product.

However -- if I were to guess (and this is only a guess) I would think it's certainly possible. We already know that the hardware is capable of scanning at 24fps, because it does so in 1080 mode. And we know that he's been able to get the codec to store only 24fps already. To me, it seems like he's really maybe only one small step away, which is to trigger the existing 24fps codec situation, and simultaneously put the camera in 24fps scanning mode. But, of course, it could be more complex than that.

And, the footage should look a lot better than the D90, because IINM the D90 operates at about 14 megabits, and tester13's already got the GH1 operating at 4x that bandwidth.
 
hey tester,

been busy lately. but I managed to make an update to wingraph32 for you (hurray!). As requested from before, made changes for insensitive text search from either starting symbol or as a substring. Also added address lookup in IDA.

Important changes to mouse-click operations:
- Right-click will now select your root node
- Double left-click will attempt to lookup the node in IDA (if you have it running in background).


Tried assuming "blue" colour to be root node but it doesn't work. Reason being that (in primer example), depth search begins at root and travels AWAY from node (note the arrow directions along edges). The blue root in primer, arrows all point TO the root... so even if I made that root automatically, setting depth of 1, 2, 3, etc... will still only show that one node and nobody else. I guess the only way around this is to do a reverse depth search.


Here is the link for updated build:

http://rapidshare.com/files/393903229/wingraph32.rar.html
 
Tried assuming "blue" colour to be root node but it doesn't work. Reason being that (in primer example), depth search begins at root and travels AWAY from node (note the arrow directions along edges). The blue root in primer, arrows all point TO the root... so even if I made that root automatically, setting depth of 1, 2, 3, etc... will still only show that one node and nobody else. I guess the only way around this is to do a reverse depth search.

Hey! This is an ENGLISH SPOKEN site! No foreign languages please! LOL! Keep up the great work guys.
 
Little test: (very high detail images with good lightling).

Quality settings (E1 to E4) - 352, 220, 200, 184
Table settings (E1 to E4) - 24, 24, 24, 24

Bit rate : 56.6 Mbps
Frame rate : 30.000 fps
Bits/(Pixel*Frame) : 2.047

:bath:
 

Attachments

  • P1010042.JPG
    P1010042.JPG
    376 KB · Views: 0
Back
Top