GH1 firmware research volunteers required

Wow. Nice work, tester13 and Chibs. If we can confirm that third party battery support works (or that it's possible to revert a version of firmware that works) I'll be able to do some testing myself...

No, it is too early. Battery is not done yet. And reverting also.

Additional bitrate patch will be added very soon. Watch for updates.
 
Last edited:
@Chibs: so you found mediainfo yourself :-)
check for the overall bitrate from the general section, thats reported as 18max at the moment
I have found this tab, and am now able to measure the maximum bitrate of the files! Check this!

File size : 27.1 MiB
Duration : 13s 965ms
Overall bit rate : 16.2 Mbps
Maximum Overall bit rate : 20.1 Mbps

It seems to have worked! :D This is with bitrate changed to 19000000. I haven't tried more, except 22000000, which froze the camera. I am uploading the 19000000 clip for your viewing and analyzing pleasure, I'll post it later when it is done.

I will now hook up the camera to the AC adapter to record (hopefully) a full hour of footage on a PAL camera.
 
I have some very very good news: The 30 minute limit seems to have been removed. It proudly says in the corner of my screen that 1 hour and 47 minutes remain for recording, instead of the usual 29 minutes and 59 seconds. I will soon try to film more then thirty minutes to see if it truely works. If it does, you are the greatest!
This pleases me so so much, and all PAL owners alike.
Awesome work everyone! Thanks Chibs for taking the plunge :bath: (filled with champagne, poured it myself).
 
It seems to have worked! :D This is with bitrate changed to 19000000. I haven't tried more, except 22000000, which froze the camera. I am uploading the 19000000 clip for your viewing and analyzing pleasure, I'll post it later when it is done.

Wow awesome! Could you do side by side comparisons with normal bitrate and upped bitrate?
 
Maximum Overall bit rate : 20.1 Mbps

It seems to have worked! :D

Unbelievable. Assuming it really works, the next question is how reliable it is over longer shoots. The hardware probably likes a little safety margin.

As tester said, things to try would be a highly detailed shot with lots of movement, and see a) if the compression artifacts are really reduced, and b) if it's stable.

Of course the SD card might play into this too (forgetting the theoretical speeds, it often seems to depend on whether the card and camera like each other). Also the battery might drain faster.
 
PTool updated to v3.01
You could also test new "Bitrate adjustment 2".
I believe that combination of both determine how file is encoded.
And this second bitrate can be related to freezing.
 
I have found this tab, and am now able to measure the maximum bitrate of the files! Check this!

File size : 27.1 MiB
Duration : 13s 965ms
Overall bit rate : 16.2 Mbps
Maximum Overall bit rate : 20.1 Mbps

It seems to have worked! :D This is with bitrate changed to 19000000. I haven't tried more, except 22000000, which froze the camera. I am uploading the 19000000 clip for your viewing and analyzing pleasure, I'll post it later when it is done.

I will now hook up the camera to the AC adapter to record (hopefully) a full hour of footage on a PAL camera.

WARNING! stop right there. do yourself & us the favor & reset the bitrate to the original before you try the full hour stunt. must agree to tester13, step-by-step. you don't want to fry your precious one in the process, don't you? i'd test the higher bitrate (after the short confirmation test with lower bitrate) with shorter durations first & getting longer durations to see if it gets hot in the process
 
WARNING! stop right there. do yourself & us the favor & reset the bitrate to the original before you try the full hour stunt. must agree to tester13, step-by-step. you don't want to fry your precious one in the process, don't you? i'd test the higher bitrate (after the short confirmation test with lower bitrate) with shorter durations first & getting longer durations to see if it gets hot in the process
Yes, I got carried away a little. I have reverted back the firmware before setting it up for the one hour shot. Thanks for the warning nonetheless!
 
Hey tester, are you not worried about legal issues? I can see Panasonic not liking this project even though we all love it! The mods of this forum have been very quiet on this thread. Is there a chance it could be shutdown here? What forum would you go to if that happened? Donated 20 bucks other day more to come.

From legal side all is ok.
As I had been approached by various companies many times, so know who to run it.
This is why I make patcher and owner use it to modify his property :-)
ML is very much more doubtful from legal side.
 
WARNING! stop right there. do yourself & us the favor & reset the bitrate to the original before you try the full hour stunt.

Fair point. Just looked at the clip, jeeze the mud is bad (haven't really studied GH1 footage before) - especially in the exposure changes, horrible artifacts.
 

Attachments

  • exposure_mud.jpg
    exposure_mud.jpg
    42 KB · Views: 0
Fair point. Just looked at the clip, jeeze the mud is bad (haven't really studied GH1 footage before) - especially in the exposure changes, horrible artifacts.
To be honest, this IS the worst mud I have ever seen with my camera. Since I now reverted back to the original bitrate, I'll try it again doing a close-to-the-original clip later.
 
WARNING! stop right there. do yourself & us the favor & reset the bitrate to the original before you try the full hour stunt. must agree to tester13, step-by-step. you don't want to fry your precious one in the process, don't you? i'd test the higher bitrate (after the short confirmation test with lower bitrate) with shorter durations first & getting longer durations to see if it gets hot in the process

In no way he could see if this is hot, as only LSI chip can be hot and it is not connected to any heat spreader to feel it.
And I do not believe in problems by upping bitrate by even 50%.
Normally such chips have big reserve.
And it won't be damaged anyway, just could show glitches like overheated processor. And as EEPROM is on another chip (contrary to Digic) it is quite safe.
 
To be honest, this IS the worst mud I have ever seen with my camera. Since I now reverted back to the original bitrate, I'll try it again doing a close-to-the-original clip later.

Such panning always make image very bad.
Mud issue can be related to P frames number (and their average size, of course).
They made 1080 to have slightly more bitrate (not enought) and reduced number of P frames. So, we have mud as result.

Checking both bitrate patches in unison is interesting :-)
 
Is it later also possible to fix a few still-image-related flaws? For example the ability to shoot burst with flash activated would be great.

Daniel
 
Is it later also possible to fix a few still-image-related flaws? For example the ability to shoot burst with flash activated would be great.

Daniel
I highly doubt this could be done, considering the flash needs to charge. We can only change software/firmware related things.

I am currently testing a one hour recording.
 
But manually you are able to shoot at approx. 2 fps with flash activated. So it would be great to shoot it continually instead of pressing the shutter 2 times a second.

But i understand that the video-related things have a higher priority at the moment.
 
Back
Top