GH1 firmware research volunteers required

Please be more specific about the external microphone patch.
The microphone uses the first three connections of the four contacts on the plug.
The remote control uses the last two rings, contacts 3 and 4 close to the base as in this
schematic

We had some talks about simple switching schematic.
Plus I just need to test such patches and see how camera behaves.
 
We had some talks about simple switching schematic.
Plus I just need to test such patches and see how camera behaves.

The best way to test this is open up one of those cheap third-party remotes and solder in a headphones extension cord using just the three first contacts.
That will make sure that a plugged in mic will not shorten out the remote control contacts.

I will give it a shot either tonight or later in the week.
Thanks for the patch. It will hopefully allow people to use external mics, or Zooms with the remote control.
 
Modified "AVCHD 1080p24/25->720p24/25" patch. I hope that changes allow to get proper 720p frame (not cut out one as before).

Please do not do this change… a cut out (crop) would be very useful if it was of the centre of the frame - for c-mount lenses. C-mount lenses would suddenly become very useful - and bargains.
 
Please do not do this change… a cut out (crop) would be very useful if it was of the centre of the frame - for c-mount lenses. C-mount lenses would suddenly become very useful - and bargains.
I think you misunderstand the issue. The patch has never worked as intended - instead of scanning a 1280x720 rectangle at the center of the sensor, it scans the upper left corner of the sensor while displaying the full sensor in the viewfinder. If this could be fixed - either by scaling the full-size sensor or with a correctly centered crop - it would be a very useful feature.
 
Btw. Test PAL recording on NTSC card (or reverse), please. It is not risky.

Just tried this, doesn't work. Camera freezes after you record one format to the card. I recorded NTSC and when I switched to PAL it froze. I didn't get an error, but image on screen froze though I could still see the histogram and exposure reading onscreen. Also tried recording PAL first before recording NTSC. And I even tried splitting the files up with an MJPEG recording between each. No go.

This was with MOVIE FORMAT PATCH enabled.

Stupid question. Are you able to update firmware using play button during TV output active?

Nope. TV Output disables firmware update.
 
PTool 3.40d updated (12.08 release)

Added "AVCHD encoder error" patch to testers section. Patch requires extensive testing. I hope it'll reduce AVCHD freezing problems.
 
Ah, I'm not experiencing freezes during recording so not sure how to approach this testing.
Isaac, I believe your main working settings are PTool "C" + Native and you are mostly using manual lenses, right? In most real-world situations (with enough motion in the frame) I think that setup will work well. However, throw that puppy on a tripod and shoot a Death Chart and you will very likely get a "native crash." Also, shoot with an AF lens in AF mode, as I've determined that to be a factor in bringing on the crash. I haven't tested new patches for about two weeks now, as I took an untested configuration and royally screwed a nice weeked of shooting, so I don't have the hands on scoop on the latest and the greatest. FWIW, I'm running the following settings with PTool current as of that post's date. Since then some patches were removed and consolidated, so results may vary with the latest dev version.

So, I would first do the static Death Chart shot to cause a crash (and confirm you don't have a special magic cam). Then add new patch into the mix and see what happens. Let's continue discussion in this thread and leave systematic reports here.
 
Ah, I'm not experiencing freezes during recording so not sure how to approach this testing.


That’s what I thought a week ago with my settings. I had no issues with 24p and a higher bitrate (for about a week or more)...until someone told me to shoot a tree in bright sunlight while the camera is on a tripod (static scene). I kept the settings anyways because i asked myself..."how often am I going to shoot a scene like that?" I could have went a month or more (maybe) until I found out the hard way. But it is good to know the weaknesses.
 
I've been trying out the latest ptool and checked the AVCHD encoder error box and results seem to be no better than before, bummer. Tried about 10 combos of various bitrates, GOPs, checking only certain bitrate boxes etc but results look similar: it's just as easy to crash the camera or replicate the blank P/muddy I bug. Also the 1080->720 resize still seems to crop off the lower right part of the image.
 
PTool 3.40d updated

GF1
Added "Manual movie modes (old version)" patch (by request).
Added "Version patch for v1.24" (this is totally untested, must be used alone by owners of cameras with v1.24 firmware!)

GH1
Added "Movie format error" patch. (removes error if you try to record PAL footage on NTSC card).

Added "Lens mount flag" patch (prevents Lens not mounted errors).
Added "External microphone" patch (makes camera think that external mic is attached, useful then external mic is used with remote shutter).
Last two patches are risky patches (system routines called before any interface), so, I warned you. But we need to know how they work to go further.



Vitaliy.

I updated my camere and checked the "Lens mount flag" option.
Now the camera is displaying "The lens is not attached properly" message and there is no way to get rid of them.
Looks like I bricked my camera.

I also checked the "Prevent version compare" option to be able to restore a Panasonic version of firmware.

But I can't load it.

I tried to change the kit lens to another 20/1.7 lens. Did not help.
Put a Pentax lens with an adapter. Did not help.
Moving the lens and pressing the mounting button did not help.

Tried to put the camera into Service Mode.
Does not work as I can't get rid of the error message.


Please help.

I placed the original 1.32 firmware on the SD, but can't make the camera go into update mode.
Any ideas?

This seems to be a very dangerous patch, so other users should be warned.
I wander what will Panasonic charge me for fixing this.
 
Last edited:
Vitaliy.
I updated my camere and checked the "Lens mount flag" option.
Now the camera is displaying "The lens is not attached properly" message and there is no way to get rid of them.
Looks like I bricked my camera.

Yes, it can be so.

Patch was very risky. It had been stated.

Despite that this error is not blocking one (like battery), this was the reason I selected this variant.
Normally you can press Play button during such error and update is working.
Try all modes of the main wheel and all modes of AF wheel. Remove battery before each try.
Try to connect camera to computer before power on.

This seems to be a very dangerous patch, so other users should be warned.

Both patches already removed from PTool release.
Sadly they had been planned to be last risky patches.
And in start of next week I planned totally remove them among few other patches.

I wander what will Panasonic charge me for fixing this.

Good idea is to try going to service center directly.
If it won't help, you need stored ROM values and replace mainboard.
 
Last edited:
Mainboard replace will be a few hundred bucks- I'm getting mine replaced right now--here's to hoping that VK beats the new firmware soon....as I'm sure I'll be getting a new mainboard with new firmware :(
 
Vitaliy.

I updated my camere and checked the "Lens mount flag" option.
...

I know this sounds obvious but have you tried switching the setting in the menu that say's no lens that lets you shoot with no lens, that's what I have been using maybe that will help... most likely not and I have no idea what I'm talking about.

hope everything works out alright
 
Last edited by a moderator:
Mainboard replace will be a few hundred bucks- I'm getting mine replaced right now--here's to hoping that VK beats the new firmware soon....as I'm sure I'll be getting a new mainboard with new firmware :(

First, just let him go to service center. This error is very common to GH1.
 
First, just let him go to service center. This error is very common to GH1.
gotcha:thumbsup: but it sounded like it was more of a 'constant' problem as opposed to an intermittent problem....which I've had both. I've owned 3 of these cams and in all of the that message every so often will come up, but not hamper my shooting-, BUT this last issue I had it became a CONSTANT message- I've had the cam looked at- and the Mainboard needs replacing and is enroute to Panasonic service center as we speak, (type):embarasse
 
Yes, it can be so.

Patch was very risky. It had been stated.

Despite that this error is not blocking one (like battery), this was the reason I selected this variant.
...

T.Y. To back up the ROM I need to be in Service mode, but can't get there.

I was hoping you have some kind of a backdoor combination of key presses to force the camera into firmware upgrade mode for emergencies like this.
Perhaps you should implement it for situations like mine where there is nothing to lose by trying it.
 
Last edited by a moderator:
Back
Top