GH1 firmware research volunteers required

Here is how tool is used during reversing:

1278734905.jpg


Rendering is seamlessly integrated with IDA, so all you must to do is to copy string number to clipboard in IDA to instantly see how it looks :-)
 
No, i went thru entire menu. Could it be audio related (auto gain)

Maybe the clue might be the ...... Ico .... before autoGain
 
Anyone know menu with two items - START and AUTO GAIN?
Plus AUTO GAIN have small submenu with two values - ON and OFF:

Hmm...I couldn't find any Auto Gain in menus either.

It might be:

1. An option to disable AGC (audio) which is subsequently disabled and not used in Menu Firmware (but variables are left)

2. Mislabeled gain control for imager (= Auto ISO)

If you can find a way to flip it on/off dtool, we could load the firware and test what happens. If audio AGC gets disabled, then it's a big win. This would allow external mixer to be connected into MIC plug without AGC messing up the levels.

Do you think there is a parameter which controls OP-amp gain as well? In that case, you could set it low and thus lower the amount of gain noise when using external audio input. It would also be a big win as it would negate the need of external audio recorder and all the fuss involved with sync in post-production.
 
Vitaliy,

I have finally figured out the key presses to get to the actual service mode, the one with all the 3 character options. Each of those options is a different test, and each has an "F" next to it, which can be changed to an "O" using the "Delete" button. The "O" turns on the test, and all the ones turned on will execute in order upon pressing the "Display" button.

To get to this mode, your camera must be in the "Permanent Service Mode" I previously described...the one where your camera consistently displays the yellow caution triangle when powering off the camera. From here it is a simple matter of:

1. Power off the camera.
2. Turn the drive mode lever to Burst mode.
3. While holding the "Film Mode" and "Display" buttons, power on the camera.

Done. You will see "SERVICE MODE" at the top, with the options for "NORMAL : >" and "ALLRESET : FILM+DEL". From here, you can press the "Display" button to get to the screen with all the 3-letter test options.

Be careful, as some of these tests are quite tricky to use, and if you enable one I don't believe there is a way to turn it off until the camera passes the test. This is especially tricky for the "KEY" test which is a test of every single button on the camera and maps each button to an alphabetical character.

Once this mode is enabled, the "ROM BACKUP" menu will have the "! > LUMIX" option enabled and no longer grayed out.

I can grab some screens from here or describe the individual tests further. I've also found a couple other magic button combinations. Perhaps you could make a separate thread for accessing service modes for the GH1, and I could add a post there summarizing all the different modes and how to get to them.

Hope this helps,
-Path
 
Last edited:
Good progress on menu and icons related reversing.

Just made hidden Multiple Exposure functionality working on BRACKETING menu item (instead of standard bracketing screens).
Multiple Exposure is in fact thing with Auto gain option, and no, it do not have any relation to audio.

Ptool with corresponding patch will be released soon.
 
PTool updated

Added patch changing bracketing settings to multi-exposure functionality.
Sadly it looks like final images combining do not work.
Or I do not understand something about this function.
 
PTool updated again :-)

Patch changing bracketing settings to multi-exposure functionality modified.
Added language selection menu patch that allow to change languages available in selection sub-menu right to corresponding menu item. Right now this is necessary first step.

P.S. Please note that we need responsible testers and developers. I am not able to reverse code, write tools and test all this myself. In result project will be dead as it happened with ML project.
P.P.S. Please do not write me messages "How I can help? Write me instructions with complete spec.". If you are unable to find task after reading this sub-forum you really a of no use.
 
Last edited:
PTool updated again :-)
P.S. Please note that we need responsible testers and developers. I am not able to reverse code, write tools and test all this myself. In result project will be dead as it happened with ML project.
P.P.S. Please do not write me messages "How I can help? Write me instructions with complete spec.". If you are unable to find task after reading this sub-forum you really a of no use.
Hey, Vitaliy. I think what would be helpful is for you to outline the basic functionality behind the more esoteric patches. Multi-exposure patch is self-descriptive (it's great that you are delving into photo functionality by the way -- I will be testing it for sure), but the Preset bitrate patches are not. What are they supposed to do? Also, several tests reports have been posted in AVCHD thread. Please provide some feedback -- we need to know if we are doing it right or wrong.

Thanks!
 
Preset bitrate patches are not. What are they supposed to do? Also, several tests reports have been posted in AVCHD thread. Please provide some feedback -- we need to know if we are doing it right or wrong.

You just ask the impossible.
I don't have some magical runes with detailed description of AVCHD compressor. All I know that this things are descrete and depend on bitrate (if you look at video bitrate adjustment between 0-16Mbits you could notice jumps). They are used to set some parameters of encoder.
 
You just ask the impossible.
I don't have some magical runes with detailed description of AVCHD compressor. All I know that this things are descrete and depend on bitrate (if you look at video bitrate adjustment between 0-16Mbits you could notice jumps). They are used to set some parameters of encoder.
Note that I asked for an "outline of basic functionality", not "detailed description" ;) Basically all I'm saying is "the more information is communicated to testers, the higher the chance their tests are more focused and ultimately results being more useful to you". IMHO.

Now, as far as the new little "Multi. Expo" menu is concerned.
1) Auto Gain doesn't seem to have any effect, but nice to see it in pixel flesh :)
2) After WB'ing Start and shooting the first picture the Menu (Next, Retake, Exit) is only displayed for 2-3 seconds, then automatically goes to "Next". Shouldn't it stay on until user makes a selection?
3) "Retake" doesn't work, just functions as "Next".

Great to see some working interface changes. In-camera HDR would be cool. I personally don't like clicking any buttons on camera when taking a series of shots for HDR merge as this sometimes introduces slight shifts in view between shots. It would be very useful (IMHO) if clicking shutter button in auto-bracketing mode initiated a full programmed sequence with minimum delay in between shots instead of how it currently waits for shutter release between each shot (why???). Having shots merged by camera would be icing on the cake. Having a menu option to either auto merge or save the full sequence or do both would place a big fat cherry on top of icing :happy:
 
Some clarification of development plans:

1279118111.jpg


This is what we try to archieve in long run.
Main part functions will be called using long jumps replacing original ones.

To make this working we must better understand menu inner workings, file based operations, etc.
Plus make special assembler.

With such thing implemented propertly development speed could be much higher(as we won't need to update firmware most of the time) and risk will be much lower.
 
Going througn menu structures reversing
I read this funny thing about software development http://www.divideandconquer.se/book-of-josh/
Panasonic menu architecture designers have many common things with guys in this blog article :-)

P.S. Anyone know why you need three versions of fopen just for system purposes, I do not cound here video-picture related twins?
How about 7 memcpy routines?
May be refactoring did not exist during education of menu developers, so copy paste was preferable method here also?
 
Last edited:
PTool 3.40d updated

Added "All Interface Languages" patch to GH1, GF1 and G1.
Patch fully replaces old "Interface Language" patch.
New patch allows you to set any language using normal Language menu.
Tested and working (but we still have problem with Chinese).
 
Last edited:
PTool 3.40d updated

"All Interface Languages" patch changed for all three cameras.

We had problems with Japanese cameras (found this one using my G1) and sometimes language was not preserved upon power-off cycle.
Now all works perfectly.
 
Back
Top