Mic for Voice Over recorded in Porta Booth- need your suggestions

Stelvium

Well-known member
HAllo friends,
as XMAS is coming i wanted to order a good mic to record the voice over in a DIY Porta booth. I don't want to spend a lot but i was thinking to stay in a range of 80-120 $. The mic should be plugged in the Tascam to record the audio.
Many thanks in advance to you gurus of the audio
 
You can't go wrong with the SE X1 and I know it is just over $200 but you get the bass cut and -10db pad that is essential for close V/O work!

The Rode mics are good too!
 
guys really appreciate your suggestions cause as a videoguy.... the sound world is a world to discover
Merry XMAS to you and your family
 
Gary what would u choose between the Rode NT1 and SEx1? I went on a video store and they showed me the AKG d140 too (they really suggested me this)
 
The Rode NT1 is a good mic and I have it's bigger brother the NT2000 but that is a a lot more.

I chose the SE-X1 as my budget mic as it has the all important 80hz high pass filter and a -10db pad so can be used closer to the source without too much proximity effect to increase the bass response and overloading of the capsule head amp.

The AKG D140 is an old discontinued dynamic mic but I have also used similar mic's for voice over too, you would be better off getting a std Shure SM58 though but as it is a tight cardioid mic you will need to get it close and most dynamic mic's are not as good in performance as a condenser mic.

It might also be worth checking out the Behringer mic's too for low budget options.
 
Well if your getting into that price range you might also look at the Heil PR-40. It's a dynamic but uses rare earth magnets and the output is close to a condensers. It has sounded very good on just about every voice I have used it on.
 
Guys my friend just brought to me his mic MK011
http://www.oktava-microphones.com/mk011.htm#tech
I'm tryng to use it inside my Portabooth but i need your suggestion about the direction toward the mic should be. I Just made a test pointing toward the mouth with an anti pop filter. The sound is good but my question for you is, that kind of mic should be pointed toward the upper side (the roof ) of the porta booth or is it correct toward the mouth of the speaker?
Many thanks Audio gurus! These are my first step in this audio world
 
The Oktava MK-011 is an END-address microphone. It points toward the sound source.
If it were a "SIDE-address" microphone (like an Oktava MK-219) then the SIDE would point toward the sound source.

Now that you have established the active DIRECTION of the microphone, how to deploy it for a particular source is an INDEPENDENT issue.
As you have observed, if you point a microphone (whether end-address or side-address) directly AT the mouth presents issues of p-popping, air blasts, etc.
So, there are several methods of FILTERING the microphone from unwanted low-frequency noise.
One of them is an "anti-pop filter" Either a big foam blob of some shape and/or an independent "screen" of some kind of material(s).

Another method that may be better (depending on the microphone and the performer) is to put the microphone angled off to the side, but still pointing at the mouth.
That gets it out of the way of the very low-frequency "noise" (p-pops, breath wind, etc.) but still captures the desired signal (speech and/or vocal music).
 
Last edited:
That most certainly is an end-address mic (like a SM58) and should be pointed towards the talent's pie hole. Probably the-closer-the-better as the mic's sensitivity is rather low.. like the (10mV) Oktava 012. Make sure the Phantom Power is 48 volts.
 
Phantom power is 48v guys!So i'll point toward the mouth and i put an anti pop filter attached to the border of the porta booth. What's the distance suggested of the portabooth between the mouth and the mic inside the porta booth?
Thx guys, i really appreciate your help
 
Mic distance is a practical and creative decision.
A practical decision based on microphone sensitivity, how much sound the person is producing, and how much ambient noise there is.
And a creative decision based on what you are doing. Is the narrator whispering ghost stories? Or are you recording people yelling at each other?
Is a close-up intimate sound appropriate for what you are recording? Or a more realistic sound from 50-100-150cm away?
Nobody can cite some particular distance without knowing (and HEARING) what you are trying to do.
 
In the timeline i noticed noise from the gain after i pumped up the volume of the voiceover. My sound guy put a filter in Vegas but unfortunately the DR100 picked up a little noise. Maybe cause i was recording with H (high) gain set?
 
Shure SM7. You won't regret it. It's a cardioid but one of the most pleasing inexpensive options. It's fantastic for just about everything.
 
Last edited:
I note people are recommending the rode NT1, what about the NT1-A? this comes in a kit with a shock mount and pop screen for voice over work.

If you are using Harlen Hogans Porta-Booth you might want to look at his mike that is apparently purpose designed for voice over work, I assume, with the porta-booth
http://voiceoveressentials.com/content/vo-1a-voiceover-microphone.htm

BTW I have not tried either the mic or the booth, only read Harlan's book on VO.
 
Last edited:
Back
Top