Using Headrest LCD a Monitor

S

SilverWolf

Veteran
I have access to a Headrest Lcd Monitor Rockwood (Xr-6450) http://store.teptronics.com/xx5hemo.html

The connection to the power is this type
http://www.eyespyvideo.com/extensioncables/pwr-09.htm

It uses S-Video connection. I'm trying to figure out how I can use this monitor with the dvx. I know I can find a battery pack with the before mentioned power connection. The way the monitor is setup there is a svideo connection coming from the monitor then another svideo cable that splits into a rca video connection and the power connection. What I wonder is can the s-video connection carry the power ?
I have no way to test this theory without buying all the equipment .
Does anybody have any info for something like this?
 
I've done something very similar. I powered the monitor with a bescor battery that has a cigarette lighter plug. I don't think the svideo connection will carry the power.
 
Well what's strange about the connection is the only cable going directly into the Lcd is a s-video connection (6-pin) Then that s-vid connects to another s-video which is split on the end with the power and rca video. Now what I can't figure out is how can that be possible ?

Also what did you use for when you did it ?
 
Are you certain that this is an S-Video (Y/C) connector or could it be just a 6 pin DIN?

S-Video uses a 4 pin DIN which looks similar in appearance to a 6 pin DIN but that may be where the similarity ends.
 
The s-video cable is to connect to the main dispaly, where its powered by the main monitor. You can find these monitors in your local wal-mart.
 
Silver. That is not an S-video connection. I have a similar LCD and it is used to connect power, ground, audio and video. Might look like S-video, but it's just a round connector for power/video

Edit: If it's new you should have the cable that connects to it and you can power it with a universal A/C adapter that does 12 volts - Just cut off tip. That's what I did - Or a battery pack from a RC car is supposed to work but have never tried... Video connection is RCA from cam.
 
Hey SilverWolf,

I looked at the link provided in detail and it can clearly be seen from the specifications that this monitor lacks S-Video capabilities. The specs read as follows:

----------------------------------------------------

Product Specifications:
Screen Size: 5.6"
System: NTSC
Power Source: DC12V+/--10%
Power Consumption: <5W
Video Input: Composition Video Signal
Operating Temperature: 0 C-60 C
Storage Temperature: -20 C-80 C

-----------------------------------------------------

The 6 pin DIN connector is likely both the power and COMPOSITE video input path. There is no mention of a Y/C (S-Video) capability. You will need to know the proper pin out of this connector to utilize the monitor.
 
Hello SilverWold,

Now that the cable/connector question has been resolved, lets look at your next question.

Since the power consumption is listed in the specifications as "<5W" then a little bit of math tells us that the current requirements would be I = P/E or I = 5W/12V or .416 Amps. From the link that you have provided, both of the adapters will provide adequate power but for a bit of headroom, go with the 1 Amp one (PWR-1AR). I am assuming that your term "power adapter" is intended to indicate an AC power source and not a storage (battery) solution.
 
I was actually looking at the AC power source and the Battery solution. Preferrably I would want both. The AC for indoor shoots and the Battery solution for outdoors and whenever a power source isn't available.
 
I actually got the monitor to work. I went to radioshack and bought the appropiate power adapter and it started working. The lcd that you showed me however looks far better than the one I have
 
"The lcd that you showed me however looks far better than the one I have"-
- - - - BUT LOOK AT THE PRICE !!!!!!!
a thousand dollar lcd monitor SHOULD look better than a $150 one !!!
 
You must log in or register to reply here.
Back
Top