Tascam DR70D // Help setting up with GH4 + Rode Videomic Go

RedChalice

Active member
I need some help setting up audio on the tascam DR70D. I have a Rode Videomic Go (doesnt run on batteries/feeds off cameras battery) connected into [ EXT IN 1/2 ] on the tascam.. Then a line out from the tascam into the GH4 mic input.. I can't get a signal.

What settings should I fiddle with to make this setup work?

Ideally I would love to dual record a cleaner signal into the camera + have a separate .wav file from the tascam.

If anyone has experience with Tascam units that could help me I'd really appreciate it.
 
What does "can't get a signal" mean?
Do you mean that you can't get anything on the DR70?
Or are you getting a proper signal on the DR70, but not on the camera?
Please be more precise in your description of the symptoms.

Have you turned on the plug-in power on the DR70?
(It is a setting in the menu.)

What happens if you plug the microphone directly into the camera? Does that work?

Did this work before? Or is this a new configuration that has never worked?

Do you know you have a good cable that is not broken, etc?
 
Last edited:
I don't see a signal in my cameras audio meters when the Tascam is used like a juicedlink (recording directly into camera through tascams line out).. I feel even when i used the tascam as a standalone recorder with the videomic go, i still didnt see levels on the tascam audio meters.

Instructions say to plug in mic into the tascams EXT IN 1/2 but cant figure out how to get a signal. Does a videomic go need phantom power in order to work even though it connects via 3.5mm into line in?
 
According to the product info…

No Battery Needed

The VideoMic Go does not require batteries for operation, but instead uses the plug-in power supplied via your camera's 3.5mm microphone input. Simply plug in, and you're ready to record.
 
I don't see a signal in my cameras audio meters when the Tascam ...even when i used the tascam as a standalone recorder with the videomic go, i still didnt see levels on the tascam audio meters.

Instructions say to plug in mic into the tascams EXT IN 1/2 but cant figure out how to get a signal. Does a videomic go need phantom power in order to work even though it connects via 3.5mm into line in?

Did you TURN ON the plug-in power for the EXT IN 1/2 as also shown in the instructions?
Did you test the microphone plugged directly into the camera?

This is the second time we are asking these questions because you have not responded to them yet.
 
Last edited:
Gentlemen sorry for delayed response. I really am grateful for you guys taking time to help.

I have turned on the plug-in power on the tascam and managed to record a signal. I was only able to do a quick test:
1) camera mic
2)rode videomic go plugged directly into camera
3)rode plugged into tascam & then a line out to camera (juicedlink type setup)
4) rode directly into tascam as a separate recorder

from my test, there was a noticeable hiss from the #3 setup. The gh4 audio levels were brought down to -11 and raised in the tascam. I recorded my tv so maybe the hiss is from a low frequency coming from tv.

The mic was tested and does work btw Mr Crowley
 
In your test #3 which audio are you listening to, that recorded by the Tascam or that recorded by the camera? If it's the camera audio you plan to use, what's the point of the Tascam in the first place?
 
If I read it right you are feeding a line level signal from the Tascam into a mic input on the camera so you will need at attenuate it 50db, the noise you are hearing is the mic amp in the camera.

i just looked at the manual for the Tascam and if you turn to page 16 you will see that you can set the outupt to LINE or in your application it needs to be set to CAM.

P.S you need to RTFM :violin:
 
Last edited:
Back
Top