Sennheiser 416 to wireless?

Steve Shovlar

DVXuser Sponsor
I have a shoot on Friday for a short news article and I am just getting everything ready. It suddenly dawned on me that I have a Sennheiser ew100 SKP100 radio mic block thingy, which attaches to the bottom a a mic like the ME66. It then transmits to the ew100 reciver attached to the camera.

Can this be used in any way with a 416? I just tried it out and nothing happened, other than fizzing, cracking and thick rancid black smoke pouring out of the mic. (only joking!)

Is there any way to make the 416 a radio mic?
 
Hi steve,
Yes there is a way...but you need the SKP500 plugon.
The SKP100 plugon will not provide +48V phantom power that the 416 requires. The SKP500 will !
(If the 416 is 12T you can buy a +48V adaptor from PSC).
It may not be the answer you're looking for but I have done this many times.
Cheers,

Brian Broz
 
Thanks Brian, as as irony I just sold a 416T a few days ago because I have a 416 P48.

So I should have held onto the 416T. Aarrgghh!

So although I have a 416 P48, I still need a SKP500 for phantom?

Thanks
 
It wouldn't have mattered Steve... both 416's require power that the skp100 does NOT provide. The T version is even worse because you need a dedicated T power supply (or a mixer that can switch to T)... and that sucks because most mics want p48 anyway... so if you want to run two "normal" mics that require power the odds of them both being T is very low. So you can't use a Mixpre with one T mic and one p48 mic at the same time... but you CAN use two T or two p48 and for most mics phantom is phantom... the p48 that the Mixpre provides will run any phantom mic from 12v to 48v.

Your best bet in a case like this is to get a Sound Devices MM-1 or some small mixer that provides phantom to the mic. Tell me one time when you don't need to know what that wireless mic is doing... and if you can't get to it to change anything then you're screwed if a problem comes up.

Q: Two situations... both use a 416 wireless.

1) 416 with SKP500. Booming a scene at some distance. Mic isn't loud enough or is TOO loud. You can adjust at the cam OR you can STOP the scene and have the boom op bring in the mic and turn up the transmitter a bit... then restart the scene. Oh and what if the boom op isn't ON the action... bad placement, etc? How will he even know? He must do his best with a reasonable guess.

2) 416 with MM-1 (or small mixer supplying phantom and line-out goes to SKP100, which you have) Booming/micing a scene at distance. Boom op has headphone out and can hear if mic is too loud or not loud enough... trims volume. He also hears if he's behind the action and losing precision... moves mic back into sweet spot. He also hears that the Harley Davidson two streets over is blowing the take even though everyone else barely notices... etc. etc. etc.


A: You want to be shooting by option 2.
 
Thanks for the info MattinSTL.

Because I can't solve the situation before Friday morning I will have to be done with lavs this time. trouble is we are on a steep beach with a prevailing wind that sweeps straight onto it. I was hoping to use the 416 by wireless, with the guy stand some distance away from me holding the mic with a Rycote, talking to the camera. I will now have to use lavs, but I will be a bit worried about the wind, which is predicted to be about 15 MPH. ( I have no shelter)

On top of this I ordered a couple of Countryman B6 lavs a week ago and they haven't yet arrived, so I will have to use the sennheiser lavs that come with the ew112 G2 setup. They sound OK sitting here at home, but on location perhaps not up to the job. I'll have to wait and see. Might spend an hour tomorrow cutting up some foam and sellotaping it around the lav to see if it will help.

I do have a 10 metre xlr cable, but it will look very unsightly coming away from the interviewee towards the camera. Don't think its a starter.

Lavs it will have to be, and the Sennheiser ew112G2 transmitter/receiver.

Thanks for the help guys. By the way the cheapest I have fond the SKP500 is £250 ($400) which seems a bit steep. I'll sell my SKP100, which has only been used just once, on Ebay and put it towards the SKP500.

cheers
Steve
 
Without proper protection lavs pick up a ton of wind noise. So make sure you have that covered.

Is there a reason you can't get some longer XLR cables and a boom, seems a lot easier solution for your problem.

Best
 
i don't know the exact model but the plug on transmitter that came with my senneiser wireless setup (the version prior to the g2) supplies phantom 48v.

i've used it with me-66 and the 416 as well.

matthew
 
seeing as you mention the beach steve, thought Id ask a question from a land-locked recordist: whats the best gear and method to not HEAR the sea, even when you can SEE it in the shot, and you need dialogue?

PS - Bummer about the lavs. I hate when that happens. Gear takes about a week or two to reach me in SA after ordering, so I understand the frustration.:angry:
 
Well the day turned out to be something of a disaster!

I had 5 large bags of gear for the day, and some stuff had to be left behind. The Army took 20 of us over to the beacj via a strip of water called the Fleet. Only a couple of hundred metres across a 6 knot tidal stream, but to walk to the same spot would have taken 4 hours without the gear. With it, impossible!

Arriving at the place the wind was blowing a force 6, or about 20-25 MPH, and I soon discovered that the lavs were a waste of space. The wind just killed it dead. We found a bit of protection behind the beach, but even there every other word had wind on it, and I had made up some sponge wind defletors. Without them noting could be picked up!

And I guess I learnt a very important lesson. Because of all the gear, I deceided to leave my 416, blimp and windsock behind because I didn't think I would use it. Massive mistake as it would have saved the day, even though it would have had to have been held by the speakers whilst they were trying to talk and demonstrate the problems on the beach. That gear should have been with me, in place of extra filters/lenses etc. Live and learn.

I learnt today that in the any reasonable amount of wind lavs are next to useless.
Even if the Countryman b6 lavs had arrived, and they still are not here, it would have made no difference. So I got nice footage but little else.

New motto: Be prepared for any circumstance when you are not able to walk back to your car to retreive it.
 
ouch. sorry man... a 416 in a blimp is a bit of a miracle really, they pretty much ignore the wind. If you have no boom man, maybe next time consider using a micstand to rig the boom static JUST out of frame (and I mean, frame TIGHT). Even as a sound man, I often use the technique on static interviews to save my arms..
 
I just had a PM discussion back and forth about Softies versus Blimp/Furry combinations. For all other readers I'll repeat myself... if you can AFFORD a Blimp/Furry over a Softie then that is definitely the way to go. It's amazing how much wind they can withstand.

If you can't afford a Blimp/Furry then you AT LEAST need fur to reduce wind. Even for lavs there's the Micro-Cat, which is totally obvious on-cam... but a foam with no airspace doesn't do much no matter what kind of mic it's on.

The last resort option is to accept a visible mic on cam (if the type of shoot allows it and it sounds like this time you could have) and then use an RE-50 with as much windprotection as needed. This mic is already good in higher winds... and then you can add a thick foam screen... and if you need to you can add fur on top of that.

If it's dramatic work where you don't want to see any mics and you need the best possible sound... then I'd expect ADR for a high wind situation anyway.

But man is Tim ever right about those Blimp systems. The first time you find yourself in a situation where you don't expect to get anything good because of wind... and you hear the results... you won't mind the high price as much.
 
Yeah.. i recently recorded and sound designed a short film set almost entirely on, next to, or IN a lake - wind was pretty much constant! I was using 2 416s in zep's. with shaggy/furrys on top, two boom ops, with a sound devices 442 going into Nagra AresBB+ digi recorder. The wind was a joke for us! the camera crew had a much harder time.

only issue I had was with lapping water sound in dialogue shots.. In the end we used a GIGANTIC polyboard with several assistants as a wave break - dipped into the water on the wind side to calm the waves hitting our shoot zone.

Super cool, those blimps. But admittedly, a lot of the time I dont use them because of the size and weight. Which brings me to the best thing about them: They cost practically nothing to rent!
 
timapter said:
ouch. sorry man... a 416 in a blimp is a bit of a miracle really, they pretty much ignore the wind. If you have no boom man, maybe next time consider using a micstand to rig the boom static JUST out of frame (and I mean, frame TIGHT). Even as a sound man, I often use the technique on static interviews to save my arms..


Very valid points.

I have the opportunity to go back there with the same group in about 8 weeks time, so basically I can redo the whole lot and get it right this time. Luckily there is no time frame for me to worry about and it won't be used until May so i do have plenty of time to get it right. However, if this had been a paying job with a 24 hour deadline I would be looking at the sack, or no more work from them!

Still, I am meeting up with the guys I interviewed and will get them to talk the same interview, and edit the footage so that we can use that soundtrack, plus I captures a ton of natural sound so I will just hopefully salvage something.
 
By the way, if you do a lot of this sort of thing, look into the ElectroVoice RE50 - if you going handheld, that thing is a beast! It really works well in horrible situations. And occasionally you can frame it out to avoid the mic in shot thing. Plus, its a dynamic mic, so you can use your plug on transmitter without upgrading.
 
Back
Top