DIY micro35 kit (New Footage!)

Re: DIY micro35 kit

Re: DIY micro35 kit

That's basically the same thing I've show above.

I'm currently changing up the spinning design to an oscillating design which will take up less space. I'm also finishing up the errecting functionality which will be handled inside the device.
 
Re: DIY micro35 kit

Re: DIY micro35 kit

Is there a reason why the main centerpiece between the camera and the external lens is so big? From the looks of the photo, it could be a lot smaller and more streamline.

I'm totally ignorant about this so I'm sure there is a good reason for its size.
 
Re: DIY micro35 kit

Re: DIY micro35 kit

It accomodates a spinning disk that serves as a ground glass. Since it's spinning, ll minor imperfections of the surface will translate into a diffuse softness on the image, so they don't appear visible as they are over your image. He just said he's trying to change the design so the box can be smaller.

I have a question: Do you record the image upside down?
 
Re: DIY micro35 kit

Re: DIY micro35 kit

The design above does record the image upside down. The next revision will include image errecting mechanisms.

Taubkin is correct, there's a clear CD spinning inside of the box. The new design incorporates a much smaller device that oscillates rather than spins.

We're very excited about the results so far!
 
Re: DIY micro35 kit

Re: DIY micro35 kit

just curious, no need to be rushing or impatient, but by when do you think you'll have a near-to/finished product with an estimated price? again, no rush, just curious!
Just wanna know if I should keep hitting refresh on this post :)
I'm excited!
 
Re: DIY micro35 kit

Re: DIY micro35 kit

I really liked the footage. I'm definetly excited to see more footage (hint, hint) and what improvements you've made on your device.
 
Re: DIY micro35 kit

Re: DIY micro35 kit

I should have some new footage up in a week or so. I should be wrapping up a doc this week. Plus my Magiqcam just arrived and I'll be testing my setup on that as well..

Thanks for the interest! Much more to come!
 
Re: DIY micro35 kit

Re: DIY micro35 kit

Yeah...what's all this spinning nonsense? Go down to the local sex shop, buy a vibrator, and glue it to the ground glass/brushed CD/whatever you're using.

Dan
 
Re: DIY micro35 kit

Re: DIY micro35 kit

First of all I checked out your pictures and I'm real impressed how you were able to used common parts to make a very well put together mini35. Great work!

Secondly the softness issue mentioned about the mini35 adapters can be greatly improved apon when you step up to larger GG. I personally decided to change mine and make it a medium format oscillating mini35 for this and many other reasons. Nearly no rez loss, all and sometimes better DOF, brighter in low light and no need for costly achromat diopters. If the the blue fringing is coming from your diopter then this could be one solution for you. You might want to look into this idea as you finalize your design and get it ready to sell. Good luck!
 
Re: DIY micro35 kit

Re: DIY micro35 kit

I'm kinda curious about the support rods and base plate. Are those purchased, or home built?

-j
 
Re: DIY micro35 kit

Re: DIY micro35 kit

The rods and base are were made by me. The rods were off the shelf and cut down to size. Then threaded. The base was cutout and tapped for the rod threads. The problem with that setup was the rods were always the same length and they were solid alumunim because they needed to be threaded. The new setup allows you to slide the rods out and tighten them down from the base plate. Much lighter.

Brett,
Could you elaborate a bit more on your design? The blue fringing is still a problem and I'd hate to throw money (expensive diopters) at it... Just means a higher selling price :(.

The new Magiqcam is sooo whip ass! I was so amazed at the results right out of the freak'n box!!! I'll probably start a new thread here or over at dvinfo with all the results.
And it works great with the micro35 kit!
 
Re: DIY micro35 kit

Re: DIY micro35 kit

The rig looks slick. The edges are just too soft for my purposes... maybe with a little more experimentation you'll solve that problem. Looks like a promising project, however. Good luck!
 
Re: DIY micro35 kit

Re: DIY micro35 kit

This seems promising, but I think the footage is a bit soft.
It looks really great, but the softness puts me off.

We'll see more tests and probably it may be a solution to what we have been looking for.
 
Re: DIY micro35 kit

Re: DIY micro35 kit

Hey, it's been 10 days since the last post. What's the scoop of the day?
 
Re: DIY micro35 kit

Re: DIY micro35 kit

Yeh, no kidding. I've been crapping my pants waiting for this to be available...
 
Re: DIY micro35 kit

Re: DIY micro35 kit

Cool as heck
don't have to order from Germany anymore!!!!!
or Birns and Sawyer (rip offs)

so please how much is it?
does it include the rods?
is it compatible with Zeis lenses?
how, where can I preorder?

pleeeeeeeeeeeeeeeeeeeeeeeeeeeeaaaaaaaaaaassssssssseeee
 
Re: DIY micro35 kit

Re: DIY micro35 kit

I'm seriously dying here waiting for you to sell these things haha... I'm ready to pay you whatever so please let us know how the progress is going...
 
Re: DIY micro35 kit

Re: DIY micro35 kit

Are there options for mounting anamorphics to this set up. I have never worked with 35mm lenses but I am sure there are som at least some form of 35mm anamorphic.

I am supposing this is a Barry question as well.

Thanks, Ryan
 
Re: DIY micro35 kit

Re: DIY micro35 kit

i've been working on a similar project as well.
i did make a few changes though.
i was able to find a pentaprism, mirror, and high precision ground glass (1500 grit non-sand blasted)
the use of a pentaprism and mirror? usually, 35mm lenses project a reversed upside-down image onto the focal plane.
using a mirror in conjunction with a pentaprism, the image is flipped and rotated for the dv cam. exactly what the mini35 does.
i haven't started building this yet since i don't have the funds, but i do have all the plans laid out. it should cost around $500.
optics were found at http://www.thorlabs.com
parts to be machined at http://www.emachineshop.com
bearings and 15mm rods at http://www.mcmaster.com
 
You must log in or register to reply here.
Back
Top