Dangerous? Plugging in and removing mic plug during recording

prexdealer

Well-known member
Hi,

I will be in a situation where I will be running a scratch track into my camera from my recorder. However, every now and then I want to use my shotgun mic or the built in camera mic, so I would need to remove the plug. Do I need to power off everything (both recorder and camera) to plug and unplug?

Or is it ok to just pull the plug when I want to get other audio? And just plug it back in when done.

Thanks.
 
The only danger is to your ears. Plugging and unplugging can make loud noises that won't make nice if you are monitoring with headphones.
 
Last edited:
It is usually suggested that you shut off phantom power when plugging and unplugging. I always have done so, so I do not know what happens if you don't.
 
Make sure phantom power is off and the levels are down before you do any plugging or unplugging.

I'm trying to figure out why you'd need to do this if you are running a signal from your recorder to the camera for scratch? Is the camera going away and having to run on its own without you?
 
Sorry if I wasn't clear. This is related to a doc I am going to do.

There are two coaches that I need to have wired with wireless lavs. I acquired 2 pairs of Rode wireless lavs through greentoe (got them about 50 bucks off retail each and no tax).

I plan to send the signal to my promix mixer (but it has been suggested that this may not make much of a difference).

I plan to then send one xlr to line into my tascam dr 60 (but I am going to get a tascam dr 40 for easier use). Then also make a backup copy. I believe that if I send one line out, that the mixer should send one lav to one channel mono and the other lav to the other channel mono. I hope my understanding is right.

I will send a scratch track to my camcorder.

However, there will be times when I will want to record audio of the players with my shotgun mic or rode mic. So I plan on unplugging the scratch line from the tascam and will plug in the shotgun mic.

The tascam will still be recording the coaches in case the coaches say something interesting.

Is this viable?

I am just trying to juggle a lot of things by myself. I would love to simplify where I can. But I really value having backup audio for this doc.

Thanks!
 
So your question is, will unplugging and plugging at the camera cause noise or other problems on the channel going to the DR40? Give it a try now and see how it behaves. There's nothing electrically wrong with doing that.

But why switch to a shotgun directly on the camera? Would it not be better to plug the shotgun into the PSC promix? I'm assuming you are referring to the PSC DV Promix 3 input mixer, which would leave you a spare input for the shotgun.
 
So your question is, will unplugging and plugging at the camera cause noise or other problems on the channel going to the DR40? Give it a try now and see how it behaves. There's nothing electrically wrong with doing that.

But why switch to a shotgun directly on the camera? Would it not be better to plug the shotgun into the PSC promix? I'm assuming you are referring to the PSC DV Promix 3 input mixer, which would leave you a spare input for the shotgun.

I really want to have redundant coverage of the coaches. I don't know how I could set up my situation which would allow me to get my backup audio files. The coaches will be screaming and yelling and I need safety tracks to account for inaudible sound.

If I run the shotgun through the mixer then while recording through the mixer, I would be missing out on the coach tracks, or at least the backup tracks. Or at least this is what I am thinking.

I am just afraid that plugging into a recorder that is powered on would somehow damage or fry the camcorder. But I guess I can quickly turn off the camcorder and then turn it back on with the mic input plugs switched.

But I am open to better solutions that allow me to keep recording the coaches all the time and getting backup lower db files, along with grabbing audio of the players.

Thanks!
 
There is no issues with plugging a hot output from a mixer to a camcorder, unless of course the XLR has some defect causing a dangerous voltage on it, in which case it doesn't matter if the camera is on or off.

Consider that what is coming out of that XLR from the mixer is a signal that is designed to go into the line level of the camcorder. So at no point is anything dangerous on the XLR. Plugging or unplugging the cable is no different than having the mixer connected to the camera and turning the mixer on/off while the camera is on (not exactly the same, but close enough).

The shotgun can do no harm to the camera since it is a passive device. The camera can do no harm to the microphone as all it is doing is presenting phantom voltage to the microphone. There is no difference between plugging the shotgun in vs turning on phantom power with the microphone plugged in.

But..... there can be grounding issues. There are cases where if you have the mixer and the camera powered by AC, then there is a remote possibility that the ground of each is at a different voltage. Funny things can happen then. If either the camera or the mixer are battery powered, there are no worries.
 
Last edited:
Paul,

Thanks for the reply. All of the devices will be battery powered.

The mixer, mics, lavs and recorders will be powered by either 9v, AA, or AAA. The camcorder will be powered by the battery it came with. So it sounds like it will be ok then. I probably will just try and turn off the camcorder as I switch.

But I am a little less stressed thanks to your reply.

Thanks!
 
Any suggestions on how to merge the audio from two wireless lavs into one mic in plug? It seems there are a lot of splitters that will replicate channels but few options from my searching that would merge two different mics. This youtube clip presents a possible solution at 2:30 (I set it to start at the right spot) https://youtu.be/DT9_QegrC_o?t=2m30s

However, the lavs used in the clip are mono.

The Rode lavs I bought are dual mono. Which I assume is like stereo (2 channels-left and right)

If I could skip the mixer and plug straight into the DR 40, which can do a stereo safety track backup, that would reduce my complexity.

Thanks.
 
Last edited:
The DR-40 also has an internal software mixer which would allow a custom mix to the phones/line out.
 
Back
Top