Difference between 1/8 port and XLR port?

the plug is only a plug , it is passive , what electronic you have behind, this is something different .
usually one mini 1/8 stereo carry one or 2 unbalance channels .
the xlr inputs usually balance and usually carry ,1 so you need 2 plugs for 2 channels.
you cannot supply phantom on unbalance input , it might supply bias ( low voltage) for electret mikes.
the shape of the plug does not have any effect on audio electronic fidelity .
the xlrs need largest surface for mounting , it cost more what influence on the price of your camera and how big it would be .
 
Exile is correct as usual regarding the general nature of the plugs.

There are a couple of reasons why one might use XLR (for example) over a mini 1/8" and they mostly have nothing to do with fidelity. In general, XLR connectors are more robust, and they can be soldered to the wire, where mini connectors are usually molded. Another reason for the "unique" design of XLR connectors is that the pins don't/can't short when you plug them in. While most modern electronics can handle this, there is the potential to fry a mic or a preamp when you have phantom power running on a balanced 1/4 connector for example. That being said I use 1/4" balanced patchbays and I jack mics with 48v all the time and it dosen't hurt them, but it does make a hideous pop :)

Lots of big studios use TT (tiny telephone) sized connectors for their patchhbays. They are smaller than 1/4" but much larger than 1/8". They save space, but because of their small surface area, they are somewhat more prone to getting gummed up.
 
Hmm... maybe I am wrong, but it seems that the 1/8 in. connector would be unbalanced, if that is the case then for a short run say 6 feet, there's no big difference, but for longer cable runs you'll loose the noise cancelling of balanced mic cables and could pic up 60 cycle noise. Mark
 
and if you run from unbalance to xlr , it would stay unbalance :-)
you can run balance signal until the camera and make the switch on the camera end , that might help ,or use transformers before the unbalance input , might even help more.
the connector it self doesn't give any indication ,1/8 might be stereo balance input , double or single unbalance , you need to see the manual :-)
 
One rule of general studio mechanics (from my days of studio work) is just as true today as it was ten years ago. Get the shortest cable you can to pull of the job. There are a couple of reasons behind this: 1. less noise possibility 2. less cable unused going to waste 3. less chance of tangling 4. less outside interaction.

I see a lot of people get these massive cables when they don't need them, and I am guilty of it as well. I used to only buy 20' midi cables when I only needed 2' cables.

In general XLR is considered more robust and 99 times out of 100 it is a stigma of a more professional audio solution. This is mostly because you cannot phantom power through a 1/8" minijack and most higher end mics or studio recording lamps require phantom power.

48V phantom power is a huge time saver and also saves money vs. buying batteries. Furthermore, there is evidence that devices operating off phantom power generate less noise (the ME series from Sennheiser is an example of this).

One final note regarding the patchbay comment, when I had my studio up and running I always used the 1/4" patchbays, because they are less expensive. I think what Tigeba was talking about is the Micronpatch bay. It uses a proprietary patch cable that are nickel reinforced and block all external noise (if this isn't the model you're talking about, sorry). I have never used on, but have seen them advertised and it's an expensive patching solution.
 
TheYankee said:
In general XLR is considered more robust and 99 times out of 100 it is a stigma of a more professional audio solution. This is mostly because you cannot phantom power through a 1/8" minijack and most higher end mics or studio recording lamps require phantom power.

.

of course you can
 
allow me to rephrase what I meant. I have not seen many/any cameras that provide phantom power through a 1/8" jack
 
Back
Top