Search:

Type: Posts; User: forbyfiev

Page 1 of 7 1 2 3 4
Search: Search took 0.01 seconds.
  1. Replies
    65
    Views
    2,092

    In January I said to my broker that I was...

    In January I said to my broker that I was interested in converting to bonds because all bubbles burst. But I got busy looking for a new car and other distractions....
  2. Replies
    65
    Views
    2,092

    We had been slow since the end of 2019 also

    We had been slow since the end of 2019 also
  3. Replies
    65
    Views
    2,092

    So I and many of my friends in the business are...

    So I and many of my friends in the business are self-employed, not W2. We have been without work for weeks now, and everything I know of that was booked into the summer is cancelled. We do not get...
  4. Thread: Sony support

    by forbyfiev
    Replies
    0
    Views
    293

    Sony support

    Is there any way to reach an actual person at Sony, for tech support? Are there any living reps available?

    I've been sending emails to various Sony tech supports but am getting no response.
  5. is there any info on how much heat led strips can...

    is there any info on how much heat led strips can handle? Has anyone wired up 200 or 300 watts of strips on a single panel? how necessary is heat sink?
  6. Replies
    337
    Views
    61,371

    I often bank 2 of the 3060A for a 1'x4' panel -...

    I often bank 2 of the 3060A for a 1'x4' panel - they will take Kino accessories. the 1x2s can still be had for about $150.
    that said I would stick with falconeyes just for color matching, unless...
  7. some good points there. That will be especially...

    some good points there. That will be especially obvious if you get the frame out in a bit of a wind, though a 6 x 6 isn’t too bad.


    I think you can get thin wall stainless tubing to replace the...
  8. standard rags are about 4" smaller than the frame...

    standard rags are about 4" smaller than the frame size, you use the ties to stretch them tight to the frame. I believe the ScrimJim frames are actual full foot measurements so it should work fine.
  9. maybe I'm missing something on your setup, but ...

    maybe I'm missing something on your setup, but

    set your camera to 3200K and forget about the gels (which will cost you almost 2 stops of output) then:

    1. use the 300 as a key in a softbox or...
  10. Replies
    7
    Views
    966

    thanks for the info Patrick

    thanks for the info Patrick
  11. Replies
    7
    Views
    966

    that DIY is clever. unfortunately if you...

    that DIY is clever.

    unfortunately if you already have the case, such as my 1557, the trekpak is not available.

    I'd love to be able to buy a couple of say, 8"x9" regular velcro dividers....
  12. Replies
    7
    Views
    966

    that was one I was hoping to use, but Pelican...

    that was one I was hoping to use, but Pelican will not sell me the divider set for one case, the 1557.
  13. Replies
    7
    Views
    966

    source fo extra case/bag dividers

    Is it possible to buy extra dividers one or two at a time? It seems I always need one more or different than I get with the kits. this applies to different manufacturers.
  14. Replies
    9
    Views
    1,652

    F3: just wondering if there might be issues with the...

    just wondering if there might be issues with the 3G versus HD SDI inputs and outputs, etc. 1680 res on the monitor vs 1920.... trying to avoid surprises
  15. Replies
    9
    Views
    1,652

    F3: thanks for the info! any thoughts on good or...

    thanks for the info! any thoughts on good or bad monitors like those?
  16. Replies
    9
    Views
    1,652

    F3: production monitor for F3

    im looking for advice or experiences with the F3 and older production monitors like one of the sony 2050 or jvc v20l. i think it will be fed out of a shogun or BMVA 4k, but occasionally straight...
  17. Replies
    337
    Views
    61,371

    I use plain old Kino grids and louvers from 2' 4...

    I use plain old Kino grids and louvers from 2' 4 banks. they fit pretty well and just velcro on.

    I sometimes will use a 12V jump starter with 12v to 24v transformer when I'm using them outdoors...
  18. Replies
    2
    Views
    4,242

    Thanks for the info Doug!

    Thanks for the info Doug!
  19. Replies
    2
    Views
    4,242

    z150 time lapse?

    maybe i'm going nuts, but I can't find time lapse (or interval, or whatever sony calls it this time) on the Z150. Is 1 fps the slowest possible? Any guidance?
  20. Replies
    11
    Views
    1,668

    this is kind of what I'm trying to do

    this is kind of what I'm trying to do
  21. Replies
    11
    Views
    1,668

    Thanks for the ideas. I was thinking of even...

    Thanks for the ideas. I was thinking of even cutting down my Miller jib, I don’t think anyone actually makes one that’s only 2 foot reach
  22. Replies
    11
    Views
    1,668

    Need very short jib

    Im looking for source for a jib with Only a 1.5 to 2 foot reach. Id like to use it on a doorway dolly. . It has to be rock solid, no travel jibs. It needs to support a fully kitted F3 or Ursa
  23. Replies
    8
    Views
    2,664

    call Gilbert at Galaxy Lighting Repair

    call Gilbert at Galaxy Lighting Repair
  24. Replies
    16
    Views
    2,169

    F3: So I have the current firmware installed now. The...

    So I have the current firmware installed now. The Abelcine profiles remains, I kind of thought they would get overwritten. Is the Sony S log picture profile available anywhere?
  25. Replies
    16
    Views
    2,169

    F3: View Post

    Thats a great question, Im in the same boat with firmware 1.37 not sure how that may affect the abelcine PPs

    Also, my EVF has a 3.5 mm composite video in. I tried it from the video out of...
Results 1 to 25 of 151
Page 1 of 7 1 2 3 4