DVX100a AUSTRALIA -PAL or NTSC ????

[TangMotorPictures]

I am planning to move to Australia. I am looking into what kind of format they use either PAL or NTSC. PAL would have more pixels I believe. But what if I bought my camera here in the U.S.A. and move there. Would I have a problem? I read some pdf files and the DVX100a also has a 25p frame rate. Now is that for other countries, maybe australia too? Or should I just buy a camera when I get to Aussie

[Film_Fanatik]

Australia is PAL, just like the UK. However, cameras are REALLY REALLY REALLY expensive over here. I know, cause I gave up on trying to buy a new DVX100A and settled for a second hand DVX100 NTSC. Since it shoots in 24p I don't think its that difficult to convert to PAL though I haven't tried it yet because I haven't recieved the camera. Its almsot certainly going to be cheaper if you buy a PAL camera in the US, but there is the added difficulty of a warranty that would be useful over here.

FYI, a DVX100A is listed on videoguys.com.au as costing $7,149 AU, about $4962 US with current exchange rates.

[TangMotorPictures]

Thank Matt,
where in australia? You didn't go with the PAL model huh? So I should get a PAL model here in the States first before moving? What about editing? Does a G4 or G5 mac and final cut pro cost more over there too?

[alpi69]

i think all these tools are cheaper in the states.
with the PCs you need to be aware of the right voltage, same with light equipment. i am not sure about AUS but in europe we use 220/240V compared to the US 110V.most PCs have a switch for that anyway, just to make you aware....

[TangMotorPictures]

Do you think If I bought a NTSC DVX100a that when I shot in Australia there would be a problem? Such as shooting 24p in a 25 p world. NTSC instead of PAL. The voltage difference?

I am still going to get G4 or G5 mac and edit on final cut pro. Does final cut pro have a converter from 24p to 25?

[TangMotorPictures]

OKAY, I now am a proud owner of a DVX100ap. Which is NTSC for the US.

But I am moving to Australia. Why did I buy a NTSC when I know I am moving to PAL land, because I will be back in California.

1) The voltage in Australia is higher, so do I just get a AC/DC adapter once I get to Aussie? Is it that simple?

2) I will still be shooting NTSC, so should I get a Sony NTSC monitor to Aussie to view my work.

3) I plan to get panasonic AG2500 miniDV deck, that plays both PAL and NTSC. What would happen if I shot on NTSC, play on NTSC mode on deck, but with a PAL monitor?

4)What about lighting? IS the voltage and flickering going to affect my shots?



There is alot of question that I know you guys can help. I have never move out the country, so I don't know how this is going to be?



Thanks much guys/gals

[readw]

Here are the answers.

1. Make sure that the spec on your power adapter is rated for 240VAC. If it is then it probably work in Australia with an adapter plug. If its only rated for 120vac then you will need to get an another power adapter. You should be able to buy one as a spare part over here.

2. A lot of monitors will support PAL and NTSC. I would suggest that you bring an NTSC monitor with you as it is more than likely going to be cheaper than trying to source one locally. Make sure it is rated for 240vac.

3. It won't work.

4. Unless your lighting equipment is rated for 240 volts it will not work over here. You could possibly get around that by changing the bulbs for 240 volt ones, ensuring the cabling is rated for 240 volts and you dont have any electronics in the equipment. But even then you may have some problems with the equipment as it will need to comply with the Australian electrical standards. A shock from 120 volts can easily kill someone, but at 240 volts it is much more efficient.

Cheers

Warren